my slic3r settings

    actually i use nunus filament 1.75mm with my qu-bd twoup with headbed, these are my actual settings of slic3r in repetierhost

     

    # generated by Slic3r 1.1.7 on Thu Apr  2 20:36:09 2015


    [filament:NuNusYellowHEAT]

    bed_temperature = 45

    bridge_fan_speed = 100

    cooling = 1

    disable_fan_first_layers = 1

    extrusion_multiplier = 1

    fan_always_on = 1

    fan_below_layer_time = 60

    filament_diameter = 1.73,75

    first_layer_bed_temperature = 50

    first_layer_temperature = 205

    max_fan_speed = 100

    min_fan_speed = 100

    min_print_speed = 10

    slowdown_below_layer_time = 30

    temperature = 200


    [presets]

    filament = NuNusYellowHEAT.ini

    print = hannes_04height_infill20.ini

    printer = TwoUp.ini


    [print:hannes_04height_infill20]

    avoid_crossing_perimeters = 0

    bottom_solid_layers = 3

    bridge_acceleration = 0

    bridge_flow_ratio = 0.734

    bridge_speed = 20

    brim_width = 0

    complete_objects = 0

    default_acceleration = 0

    dont_support_bridges = 1

    external_perimeter_speed = 70%

    external_perimeters_first = 1

    extra_perimeters = 1

    extruder_clearance_height = 20

    extruder_clearance_radius = 20

    extrusion_width = 0

    fill_angle = 45

    fill_density = 20%

    fill_pattern = rectilinear

    first_layer_acceleration = 0

    first_layer_extrusion_width = 200%

    first_layer_height = 0.381

    first_layer_speed = 70%

    gap_fill_speed = 20

    gcode_comments = 0

    infill_acceleration = 0

    infill_every_layers = 1

    infill_extruder = 1

    infill_extrusion_width = 0

    infill_first = 0

    infill_only_where_needed = 0

    infill_speed = 30

    interface_shells = 0

    layer_height = 0.381

    min_skirt_length = 0

    notes = 

    only_retract_when_crossing_perimeters = 1

    ooze_prevention = 0

    output_filename_format = [input_filename_base].gcode

    overhangs = 1

    perimeter_acceleration = 0

    perimeter_extruder = 1

    perimeter_extrusion_width = 0

    perimeter_speed = 25

    perimeters = 3

    post_process = 

    raft_layers = 0

    resolution = 0

    seam_position = aligned

    skirt_distance = 6

    skirt_height = 1

    skirts = 1

    small_perimeter_speed = 20

    solid_fill_pattern = rectilinear

    solid_infill_below_area = 70

    solid_infill_every_layers = 0

    solid_infill_extrusion_width = 0

    solid_infill_speed = 30

    spiral_vase = 0

    standby_temperature_delta = -5

    support_material = 0

    support_material_angle = 0

    support_material_enforce_layers = 0

    support_material_extruder = 1

    support_material_extrusion_width = 0

    support_material_interface_extruder = 1

    support_material_interface_layers = 3

    support_material_interface_spacing = 0

    support_material_interface_speed = 100%

    support_material_pattern = honeycomb

    support_material_spacing = 2.5

    support_material_speed = 25

    support_material_threshold = 0

    thin_walls = 1

    threads = 2

    top_infill_extrusion_width = 0

    top_solid_infill_speed = 25

    top_solid_layers = 3

    travel_speed = 50


    [printer:OneUp]

    bed_size = 80,96

    end_gcode = M104 S0 ; turn off temperature\nG1 Z90 F5000 ; lift nozzle\nG1 X0 F5000 ; x 0\nG1 Y0 F5000 ; y0\nM84 ; disable motors

    extruder_offset = 0x0

    gcode_flavor = reprap

    layer_gcode = 

    nozzle_diameter = 0.4

    print_center = 40,50

    retract_before_travel = 2

    retract_layer_change = 1

    retract_length = 1

    retract_length_toolchange = 10

    retract_lift = 0

    retract_restart_extra = 0

    retract_restart_extra_toolchange = 0

    retract_speed = 30

    start_gcode = G92 X0 Y0 Z0 ; zero all axes\nG1 Z5 F5000 ; lift nozzle

    toolchange_gcode = 

    use_firmware_retraction = 0

    use_relative_e_distances = 0

    vibration_limit = 0

    wipe = 0

    z_offset = 0


    [printer:TwoUp]

    bed_size = 160,160

    end_gcode = M104 S0 ; turn off temperature\nG1 Z90 F5000 ; lift nozzle\nG1 X0 F5000 ; x 0\nG1 Y0 F5000 ; y0\nM84 ; disable motors

    extruder_offset = 0x0

    gcode_flavor = reprap

    layer_gcode = 

    nozzle_diameter = 0.4

    print_center = 75,75

    retract_before_travel = 2

    retract_layer_change = 1

    retract_length = 1

    retract_length_toolchange = 10

    retract_lift = 0

    retract_restart_extra = 0

    retract_restart_extra_toolchange = 0

    retract_speed = 30

    start_gcode = G92 X0 Y0 Z0 ; zero all axes\nG1 Z5 F5000 ; lift nozzle

    toolchange_gcode = 

    use_firmware_retraction = 0

    use_relative_e_distances = 0

    vibration_limit = 0

    wipe = 0

    z_offset = 0


    [settings]

    autocenter = 1

    mode = simple


    Kommentar schreiben

    Kommentare: 0